A fire hose is a high-pressure hose that is used to extinguish a fire by delivering water or another fire retardant (such as foam). It connects to a fire engine or a fire hydrant when used outside. A firehose's normal working pressure ranges from 8 to 20 bar, with a bursting pressure of up to 50 bar. A fire hose is typically hung to dry after use since standing water in a hose for an extended period of time can degrade the material and making it unreliable or worthless.
Fire hose is a vital and important tool for firefighting. It is commonly used in urban firefighting, forest firefighting, maritime firefighting, and industrial firefighting.
The fire hose reel, which is widely used in urban firefighting, forest firefighting, maritime firefighting, and industrial firefighting, is an essential and significant firefighting tool.
Agricultural hose is light and sturdy, and it's easy to store. It's commonly used in irrigation and drainage systems in agriculture.
Fire hose should be kept cold, dry, and aired while not in use. When put onto a fire truck or vehicle, it should be stowed in a fashion that allows for air circulation and reduces chaffing against the sides of vehicle lockers due to vibration.
After performing a pressure test, inspect the hose's external surface for cuts, gouges, burn marks, and abraded regions.
After coming into touch with oil or chemicals, use a stiff brush to apply a light detergent to the afflicted region. The area should then be thoroughly cleaned with plenty of clean water.
Care in Use
- Pressure testing should be done at least once every twelve months and after each time the system is used. Each hose should be visually inspected before being hydrostatically tested at a pressure that is 50 percent greater than the intended working pressure or 10 bar, whichever is higher. Wherever possible, leaky areas should be fixed and retested.
When the hose is kinked, avoid dragging it over sharp objects or rough surfaces.
- Make sure the hose doesn't spend too much time in touch with hot, blazing debris.
- To reduce abrasion damage from vibration, cover the hose with a suitable bandage where it reaches the ground after leaving a pump delivery outlet.
- Rather than flaking, coil the hose.
Always avoid bending hose at an acute angle, especially while it is under pressure.
Hose ramps should be utilised when vehicular access is required to avoid cars running over the hose.
Couplings or branchpipes should never be dropped onto a hose since the impact could damage the lining.
Maintenance after Use
Type 3 covered hoses should be wiped off with a moist cloth after routine usage and stored in a cool, dry, well ventilated location. To maintain coupling retention and avoid detachment during usage, recoupled hose should constantly be examined and proof pressure tested.
1 inch to 12 inch
Silicone hoses are used to link metal pipework and components in cooling systems that use water or ethylene glycol. Our 90 degree elbows are ideal for creating right angle bends in pipe work, and when coupled together, they can also produce S bends. When compared to rubber, silicone hose is exceptionally flexible, with the capacity to keep that suppleness over time. Rubber hoses can split, harden, or dry rot in certain conditions, which is why silicone hoses are used in many trucks, buses, high-performance cars, and other vehicle and industrial applications.
Because we want all of our 90 degree silicon hoses to be capable of conveying fluid and air at very high pressures, we increase the number of plys and wall thickness as the diameter increases. Our silicone hose is the way to go if you're designing a racing vehicle with turbochargers or superchargers.
Liners and Reinforcement Materials:
Molded silicone couplers with various liners and reinforcement materials are offered for very demanding applications. Here are a few examples of common types.
- For additional strength and high-temperature resistance, fabric reinforcements are usually made of polyester or aramid in a four-ply design.
- Silicone connectors are protected by metal wire reinforcements from high pressures, such as vacuum pressures, which can cause silicone couplers to collapse.
- Specialized qualities are imparted by lining materials. A fluorocarbon liner, for example, can improve the resistance of a silicone connector to petrochemical wastes.
1 to 4 inch
Polyurethane combines the finest of both plastic and rubber qualities. Abrasion and tear resistance, strong tensile and elongation values, and a low compression set are all features of this material. Polyurethane is a naturally flexible material with nearly limitless flexural properties. Polyurethane distinguishes itself from most other thermoplastics by combining outstanding chemical resistance with excellent weathering qualities. PU tubing and hose, also known as PUR tubing and hose, offers remarkable resistance to most gasolines, oils, kerosene, and other petroleum-based compounds, making it an ideal choice for fuel lines (however additives in today's gasoline and petroleum products necessitate field testing).
There are some significant distinctions between the two fundamental urethane formulations, ester and ether. The physical qualities of ester-based urethane are significantly reduced when exposed to water. Hydrolytic stability of ether urethanes is significantly superior, especially in humid settings. Ether-based materials also outperform ester-based materials in terms of fungal resistance.
Temperature Range: -40oF to +160oF for all diameters.
85A – 95A vacuum rating To 28” Hg on the durometer
Tolerances for diameters: 1/8” – 9/16”: +.005”
Safety Factor: 3:1 Working Pressure UV Protected.
95A: NSF61, meets UL94HB. Base Resin Compliance: 95A: NSF61, meets UL94HB.
95A: Hose Barb, Push-In is a recommended fitting.
4 MM TO 16 MM
BLUE, TRANSPARENT, ORANGE AND BLACK COLOR
For venting high-temperature air, smoke, and chemical fumes, we provide a variety of heavy-duty ventilation ducting choices. We provide venting hose items that can withstand temperatures ranging from 160 to 800 degrees Fahrenheit and can handle the rigorous circumstances demanded by your tasks. Abrasive chemicals must be moved to another place using ventilation ducting in many high-temperature tasks. To thoroughly assess the compatibility of your medium with hose materials, consult our chemical resistance guide or contact customer support.
The activities of our everyday, modern lifestyles require that we maintain air quality. Ventilation ducting is an important part of preserving this air quality in any location. We have the correct flexible ducts for you to vent air, light gases, smoke, water vapours, warm or cooled air. Flex ducting is available from BRS for usage in autos, air conditioning, aviation, mines, paint booths, and industrial fume exhaust. Ventilation ducting is available in sizes ranging from 2” ID to 60” ID. To suit the demands of venting hose, we use a variety of materials such as PVC, polyester/neoprene, aluminium, stainless steel, and hypalon. We can provide you with the correct flex ducting for the task because of the variety of goods we provide, whether you need heat tolerance, chemical resistance, flexibility, durability, or a combination of all four.
EN 853 steel wire reinforced hydraulic hose specifications: It is made up of three parts: a tube, reinforcement, and a cover. Tube: high-quality synthetic rubber compositions provide abrasion and corrosion resistance to the hose. One layer of high tension braided steel wire reinforces the hose, making it resistant to high pressure. Synthetic rubber with abrasion, weather, ozone, and ageing resistance. Temperature range: -40°C to +100°C (-40°F to +212°F).
Hydraulic hose is mostly utilised in hydraulic systems with high pressures. It's commonly used to transport glycol, mineral oil, fuel, lubricants, emulsion, and other liquids. It's abrasion, corrosion, and high-pressure resistant. There are three pieces to it: tube, reinforcement, and cover. Because of the tube, it is abrasion and corrosion resistant. It can also withstand high pressures thanks to the high tensile steel wire reinforcing. Furthermore, the cover with the fabric imprint makes it resistant to weather, ozone, ageing, and sunlight.
1/4, 5/16, 3/8, ½ 5/8, ¾, 1, 1.25, 1.5, 2, 2.5, 3, 4 inch
40 Bar up to 400 bar
R1, R2, 4SP
Our high-pressure water hoses are made up of three layers. Smooth black SBR is used to make the tube. It can withstand air, water, and oil spray. High-tensile synthetic cord with wire helix serves as the reinforcement layer. The cover is made of the same material as the inner tube. That is to say, the cover is made of corrugated black SBR or EPDM and is abrasion, weather, and ozone resistant.
Water jetting hose is another name for high-pressure water hose. Because of the high pressure feature, it can assist in cleaning yards or outdoors with less effort. As a result, it is widely employed in a variety of industries, including construction and agriculture. It can also be employed in our daily lives for firefighting, as high-pressure hoses are required for transferring water to put out a fire. The working temperature varies from -30 to +85 degrees Celsius (-22 to +185 degrees Fahrenheit).
¼ inch to 2 inch
Food-grade hoses make it possible to move a wide range of meals, beverages, and sanitary items in a clean and safe manner. Our goods come in a variety of structures and can be customised in terms of colour, pressure, size, and temperature to match the needs of our customers. Our food grade hose and tubing satisfy industry standards, and our hose pipes can be used in a variety of applications. They also have full suction and kink resistance, allowing them to be used in a variety of situations.
For a number of uses, such as citrus/juices, wheat, potable water, oil, grain, and so on, we have a variety of sizes and colours available. We have PVC and rubber in stock, as well as suction and discharge applications. We provide a wide range of sizes, ranging from 1/8” to 6”, with bigger sizes available on special order.
½ inch to 4 inch
ELECTRICALLY CONDUCTIVE VERY FLEXIBLE, EASY TO INSTALL WITH FASTER ROUTING AND SIMPLE MAINTENANCE ROBUST DESIGN, RESISTANT TO STRESS, CORROSION, AND ENVIRONMENTAL EFFECTS ISO 15500-17, MSHA STANDARDS EXCEED NFPA 52, ANSI/CSA NGV 4.2-2014 AND CSA 12.52-2014 ELECTRICALLY CONDUCT.
External pin-pricked anti-abrasion RED waterproof polyurethane covering, inner core in electrically conductive polyamide, reinforcement in high toughness textile fibre braid. On request, a twin-line or multi-line variant is available.
According to the ISO 8031 standard, the hose's electric resistance is less than 0.12 M/m.
The CNG Series hoses were designed for high-pressure CNG transmission.
The use of a "anti-kinking" solution is especially advised for valve connections and vehicle coupling.
temperatures ranging from -40°C to +85°C (-40°F to +185°F)
1:4 safety ratio
700 mm Hg; 0.93 bar
MSHA and ISO 15500-17 criteria are met or exceeded by the hoses.
** IRAM conforms to NAG E409:2005 standard. Exceeds NFPA 52, ANSI/CSA NGV 4.2-2014, and CSA 12.52-2014 criteria.
¼ inch to 4 inch
40 bar to 400 bar
Suction and discharge hoses (also known as suction and delivery hoses) are one of the largest hoses we make in terms of diameter, and they're normally composed of flexible PVC with a helix. Depending on the use and endurance required, the flexibility of these hoses can range from rigid to ultra flexible.
These hoses work under negative pressure, which means they may pull water, slurries, and a variety of other things from a static source like a tank or pool. Depending on the hose, they can survive a wide range of temperatures, however they're usually built to tolerate vacuum rather than pressure, abrasion, or heat. The PVC helix, which may be found in most suction hoses, helps to prevent crushing and kinking.
1 to 6 inch
BRS specialises in supplying the industry with commercial rubber sheets. Our sheet rubber collection includes a variety of elastomers such as EPDM, SBR, NBR, and Butyle, among others. Each of these rubber goods is designed for a certain purpose. Some of them, such as a natural gum rubber sheet, are ideal for general sealing. Others, such as silicone sheet rubber rolls, are designed for very high or very low temperature uses. We take aesthetic issues into account as well, as we provide a variety of colour rubber sheets. If you require a rubber sheet for your application, we are likely to have the appropriate sheet rubber on hand.
All of our rubber is available in a variety of forms, including rubber sheet, rubber sheet roll, rubber strip, rubber pads, and cut gaskets, and we can provide it in whatever size and quantity you desire.
The following are our rubber and material sizes and supply options:
As needed, custom cut to order when normal sizes don't fit.
Standard sheet roll width or cut-to-order width
By the metre, roll, or cut to order
One-time, weekly, monthly, etc., or as needed
Our Butyl Rubber Sheeting is a high-quality rubber that can withstand extreme temperatures. Butyl rubber is a mixture of polymers containing a small amount of isoprene. Butyl Rubber is a versatile general-purpose rubber that can be utilised in a variety of applications, including pond linings. Because butyl rubber sheeting has strong chemical resistance, it is widely employed in a variety of industrial applications. Butyl Rubber's biggest distinguishing feature is its air impermeability, which is 70% better than most other rubbers, making it ideal for tyre tubes and tubeless tyre inner liners. Because butyl rubber sheeting is highly impervious to gases, ozone, ultra violet light, chemicals, and weathering, it is employed in a variety of additional applications. The surface of this sheeting is smooth.
|Application:||Chemical Resistant, High Temperture, Oil/Fuel Resistant, Weather/Ozone|
|Product:||Butyl Rubber Sheeting|
|Hardness (Shore A):||65°|
1 mm to 12 mm
Extremely flexible — Our distinctive green hoses are made of a proprietary polymer blend that provides for all-weather flexibility, even at subzero temperatures (-40° to 140°F), making them ideal for usage in the most extreme environments. Extremely long-lasting — Designed to withstand any industry and environment. This hose is always ready to operate thanks to its abrasion-resistant outer cover and crush-resistant anodized aviation aluminium fittings. Under strain, it won't kink – Our hoses are comprised of a memoryless hybrid polymer, which means they will lay flat, resist kinks, and coil readily, making storage a snap. There are no leaks, and the water is safe to drink -Superior O-rings are included in every garden hose, assuring a long-lasting and leak-free connection. Because our hybrid polymer is lead-free, all hoses can be used to drink water. Lightweight - It's easier to handle and navigate about the yard than typical garden hoses because it's lighter.
- Exceptional results
- Material flaws are covered by a warranty.
- High-quality, long-lasting skin
- Performance under duress
- Flexible hose for all seasons
- Hose that resists abrasion
5/16 inch to 2 inch
Various thickness available.
SAE 100R14 is a standard that is used in the automotive industry. The PTFE hose core is made of this material. Because no colours or additives are used, the hose liner has a translucent look that is free of contamination. Wire braiding is made using AISI 304/S15 quality hard drawn tensile stainless steel wire (1 or 2 wire available). For applications involving the transmission of electrically resistive fluids at high flow rates, reduced static versions of all hoses are available. Hose with a smooth bore All of the hoses in the following range have been completely approved to SAE standards and are currently available from Pacific Hoseflex. We believe that this will become the global size range for PTFE hoses, and we propose that you choose from this range for your smooth bore hose needs. If the coupling size limits your options, we provide three more smooth bore hose ranges from which to choose the exact size that best meets your needs. For steam-cold water cycling, normal wall products are not suggested.
Single Stainless Steel Braid, Double Stainless Steel Braid Reinforcement (Type 304)
-54°C to +232°C (-65°F to +450°F) temperature range
¼ to 1 inch
-250 to +250-degree Celsius
Industrial steam hose is designed to handle saturated steam and superheated steam continuously below 235°C or intermittently below 160°C. High-quality rubber is used to make the steam hoses. And steam hoses with braided steel wire reinforcing layers are very resistant to heat and high temperatures.
Applications for steam hoses include:
In all branches of industry, it is ideal for steam cleaning, steam hammer, vulcanizing machines, injection moulding machines, and hot pressing equipment.
- Long life expectancy.
- High temperature, corrosion, and high pressure resistance are all excellent.
- Flexible and light-weight.
- High tensile strength and anti-destructive properties.
Here are the steam hoses we offer:
Wire braid steam hose and PTFE steam hose. Mechanical, electronic, military, and chemical industries are among the industries that use PTFE steam hose. Because of its corrosion and high temperature resistance, it can transport extremely corrosive media at a high temperature of 250°C.
¼ to 8 inch
500 degree Celsius
The stainless steel clamp is used to keep two pieces in a cylindrical socket together and assure their tightness (pipes, hoses, etc.). Rack, screw, trunnion, and ear clamps can all be attached in numerous ways. The metal clamp is adjustable and fits all pipe diameters. It is appropriate for all types of industrial maintenance and can be installed in a wet environment and is resistant to corrosion, fire, and temperature fluctuations.
A clamp is a fastening mechanism that uses inward pressure to hold or secure things closely together to prevent movement or separation.
- Steel, galvanised band collar
- galvanised steel screw
- Connect medium and heavy duty hoses to connections on mobile and stationary units with this special clamp.
- highly durable
- The bandwidth is around 20–26 mm.
- Band thickness is between 0.8 and 1.6 mm.
- a single clamping screw
½ inch to 24 inch
To unclog a sewage, a sewer jetter is a heavy-duty lightweight hose that connects to a pressure washer: Drainage Systems Drains for landscaping Lines of sewerage The sewer jetter hose can be inserted into the main sewer line, which is normally found outside of a home or business. Other sewer connections, most of which are located in the basement, may be available for cleanout inside the home or office. The back-firing jets on the sewer jetter nozzle will draw the hose into the drain for you when you turn on the pressure washer. As a result, it needs less physical effort on your side than cleaning the drain using another method. If you were to use a mechanical drain cleaning, for example. When your sewer jetter is ready to use, it will scour the sewer line for any obstinate particles. The water efficiently sweeps over anything in its path as it flows deeper into the line.
¾ inch and 1 inch
High pressure for sever cleaning
Wearing a hazmat suit provides full coverage when dealing with chemicals and pollutants. Dupont Tyvek suits and Onguard are two popular brands and designs that we carry. The HazMat Coverall Tyvek Suits, for example, are our most popular suits for professionals and home improvement workers. The materials used to make this disposable clothing vary based on the type of chemical or organic compound resistance you require. We also have kits that include a respirator. Our most popular Lead and Asbestos Removal Kit, for example, provides the most reliable protection. In conjunction with hazmat suits, the 3M 6000 Lead & Asbestos Mask Combination is our most recommended kit for lead and asbestos protection. Below is a list of our biohazard suit products. Some are sold individually, while others are offered in cases.
Radiator hoses are essential parts of your car's cooling system. They cool the engine by transporting coolant through it and absorbing the excess heat created. They are attached to the car's engine and radiator. The coolant then completes the cycle by returning to the radiator and releasing the heat through the cooling fins before repeating the process. The underlying technique that prevents your car from overheating is this simple cycle.
In your engine, there are two radiator hoses. They're also known as the 'top' or 'bottom' hose, as well as the 'inlet' or 'outlet' hose. After the coolant has passed through your engine block and is now hot, the inlet or top hose feeds it to your radiator. The outlet or bottom hose, on the other hand, returns the now-cool coolant from your radiator to your engine.
If your radiator hoses fail, coolant will flow all over your engine and your engine will overheat. Because this is both dangerous and costly to fix, it is critical to have your radiator hoses inspected and replaced as soon as possible by a qualified service provider.
To ensure effective engine cooling and vehicle safety, BRS uses high quality materials such as high grade synthetic rubber and rayon fibre reinforcement in our premium quality radiator hoses, as it does with all of our parts.
1 inch to 4 inch
These stoppers are useful in preventing water leaks. They are often used in heavy construction joints because they are strong and effective at preventing leaks. The PVC water stopper is tested for the possibility of malfunction in concrete structures as a result of climatic and geo-disturbances, as well as frictional bottlenecks.
Area of Use:
- Dams, locks, canals, and water reservoirs are all examples of infrastructure.
- Structures for primary and secondary confinement.
- Culverts and tunnels are two types of culverts.
- Facilities for the treatment of water and waste water.
- Buildings for commercial and residential use.
- Plant for Water Treatment.
- Abutments for the bridge and deck.
- Tanks for storing goods.
- Flood Walls and Retaining Walls
- Chemically inert.
- The finish is outstanding.
- Long-term use.
- Fitting is simple.
- Store of Hardness
- Resistance to chemicals.
- Tensile Strength is a measure of how strong something is when it is stretched
- Absorption of water.
- Brittleness at low temperatures.
All of our PVC Waterstops have been professionally designed and produced to meet or surpass industry standards.
6 inch to 12 inch
2 mm to 10 mm
Petroleum hoses are used to transport petroleum goods, including as liquid products from the refining process (primarily fuels and oils), as well as crude oil and semi-processed petroleum products. Crude oil, gasoline, kerosene, heating oil, diesel oil, hydraulic oil and lubricating oil, hardening oil, machining oils and emulsions, honing oil, thermal oil (heat transfer oil), transformer oil, various types of solvents, maintenance oil, asphalt and asphalt emulsions, and other liquid bituminous substances are all examples of petrochemical products.
Hoses and hose assemblies are used for petroleum extraction and processing, liquid petroleum product transfer, loading, and unloading (e.g., oil tankers in ports, tank trucks, rail tankers), oil and fuel distribution and refuelling (e.g., petrol pump hoses, heating oil delivery hoses), technological processes in the industry, vehicle fuel systems, hydraulic installations, and so on.
Consider the following while choosing a hose: Resistance to specific aromatic hydrocarbon content in fuel, resistance to modern fuel additives and oil additives (unleaded fuel, biodegradable fuel, transformer oils), and any special requirements for static charge protection (copper wire, antistatic rubber, conductive rubber), particularly in potentially explosive zones
Petroleum hose couplings and fittings (see INDUSTRIAL FITTINGS) should be crimped with ferrules using crimping machines or installed with worm-drive clamps, bands, and bolt clamps.
¾ inch to 2 inch
Nitrile Rubber is a butadiene-acrylonitrile copolymer that is utilised as a general-purpose, oil-resistant polymer in a variety of applications. The resistance of Nitrile Rubber to oil increases as the percentage of nitrile in its composition increases. As a result, it's an excellent copolymer for rubber seals and gaskets in the transportation industry.
Nitrile-Butadiene, Acrylonitrile Butadiene, and Buna-N are all names for the same substance. Butadiene and acrylonitrile react to form NBR, which is a copolymer.
NBR is often used at temperatures ranging from -40 to 275 degrees Fahrenheit.
It has good resistance to fuel, solvents, mineral and vegetable oils, and hydraulic fluid in addition to oil. This trait could be combined with a moderate ability to withstand ozone exposure.
12 inch to 48 inch
1 mm to 12 mm
A high-pressure mud hose, also known as a rotary hose, vibrator hose, or jumper hose, transports drilling fluid from the mud pump to the drill floor's mud standpipe manifold. It comes in bore sizes ranging from 2" to 6" and lengths up to 120 feet. API end fittings, such as NPT thread and flange, and other specified fittings, are offered to fulfil various market requirements. A carefully compounded synthetic rubber tube and cover line the mud delivery hoses. They offer exceptional resistance to abrasion and oil corrosion.
- For petroleum drilling fluids, use an oil-resistant tube.
- Ozone, abrasion, and weather protection are all covered.
- Multiple spiral layers of high-strength steel wire serve as reinforcement.
- Hose inside diameters are 2′′, 2.5′′, 3′′, 3.5′′, 4′′, 5′′, and 6′′.
- maximum length is 120 feet.
- safety factor is 2.5.
- -22°F to 200°F (-30°C to 93°C) is the operating temperature range.
- Up to 7500psi operating pressure.
- API flanges, MPT threads, butt-welded unions, or as needed as end fittings.
- API 7K certification.
½ inch to 4 inch
Every industrial hose application requires something a little different, whether the pressures are high or low, the transfer rates are sluggish or fast, and the ingredients are as basic as air and water or as complex as dangerous chemicals. Because of this, BRS industrial hose products are made from a range of compounds and reinforcements that can be color-coded and branded for quick and easy identification.
Textile-reinforced industrial hose specifications:
It is made up of three parts: a tube, reinforcement, and a cover.
Tube: mostly nitrile, a high-quality oil-resistant synthetic rubber.
One layer of braided cloth reinforces the hose, making it lightweight, flexible, and simple to use.
Cover: high-quality synthetic rubber, primarily neoprene, that is oil and weather resistant.
Temperature range: -40°C to +100°C.
Drilling hoses have a wide range of applications in mineral extraction, including oil and gas extraction. A drilling mud, usually technical water, hydrogel solution, or clay-based solutions, is injected into the well with the help of the drill pipe at a very high pressure. Drill hoses are also utilised between oil tankers and offshore drilling wells. Drilling hoses can be used to drill wells in the sea on both stationary and mobile drilling rigs. Drilling hose is also used to dampen vibrations in rotary plants. It is formed of a short length in this situation and functions as a compensator.
Production process and construction:
The drilling hose is made up of numerous rubber layers layered on top of each other and a metal braid.
- A specific rubber and synthetic material is used to make the base, which is an interior rubber tube.
- The textile braiding is the next stage.
- The power metal braid is constructed of high-strength aluminium wire that is coil-wrapped around one of the rubber layers.
- The drilling hose's exterior layer is comprised of an unique rubber mix that is abrasion, flame, and UV resistant.
Buy hoses for drilling and vibration absorbing:
Drilling hoses are available in metres and fixed coils of 3, 6, 9, 18, 21, and 24 metres.
Price for drilling hoses:
The cost of drilling hoses is determined by the materials used.
½ inch to 3 inch
20 to 100 bar
Extrusion or vulcanization are used to create flexible hoses. The non-metallic flexible hoses are reinforced with a crisscrossed grid of fibres that are braided, spiralled, or knitted together to enhance strength. These reinforced hoses can be made as long as you need them to be. Flexible hoses are made up of four components: an inner tube, reinforcement, end fittings, and a protective outer cover.
1 inch to 8 inch
0-70 degree C
Use for air, powder, water, fumes etc
EPDM/NR rubber reinforced with steel braiding is also used to make concrete hoses. Rubber volume loss stated in cubic millimetres according to ISO 4649 (formerly DIN 53516) determines the abrasion resistance of the inner rubber layer; the smaller the value, the stronger the hose material's abrasion resistance.
1 inch to 4 inch
10 bar to 100 bar
We provide a variety of PVC Braided Hose that is specifically built for low pressure applications and is available at extremely reasonable pricing.
Basically, this hose is made of high-quality PVC that has been braided into a pattern to assure its relevance. Oil, water, and acids can all be used with these. 1/2′′, 3/4′′, 1′′, 1 1/4′′ 1 1/2′′, 2′′.
- TPU (thermoplastic polyurethane) in two layers provides excellent biocompatibility.
- It is reinforced with nylon braiding, allowing it to withstand great pressure while remaining extremely soft.
- 360 degree high joint with rotating male Luer lock with standard PC Luer Male and Female locks
- 150 psi constant operating pressure
- a burst pressure of more than 300 psi
- Bending resistance
- Sizes can be made to order.
- Sterilization or non-sterilization is determined by the needs of the customers.
¼ inch to 2 inch
By preventing external contamination, retaining taste integrity, assisting in fast flavour changeover, and being impervious to gas permeation, the beverage distribution sector benefits. Whether it's for cold, heated, carbonated, alcoholic, or any other type of beverage, BRS offers the right dispensing hose for the job. All are made under ISO 9000 guidelines and comply with industry standards such as NSF-51, NSF-61, FDA, 3-A, and ASTM E84-94.
- Soft drink vending machines
- Dispensing equipment for ice tea and fruit juice
- Carbonated beverage systems that are frozen
- Espresso and coffee machines
- Dispensing apparatus for dairy products
- Lines for carbonated and non-carbonated water
- Dispensing equipment for condiments
- Dispensing equipment for hot cheese
- Lines for carbon dioxide, nitrogen, and a mixture of gases
½ inch to 4 inch
Air Compressor Hose can be used in a variety of settings, including industrial, commercial, and residential. This Air Compressor Hose is extremely tough, with a working pressure of 300 psi and a burst pressure of 900 psi. For further strength, it is reinforced with two layers of spiral polyester yarn. For flexibility and oil resistance, the cover is smooth EPDM rubber. We have a large stock of air hose assemblies in various sizes and styles.
It's critical to invest in a good air compressor hose to ensure steady air pressure, a tight seal, and consistent power output, but with so many options on the market, it can be tough to know where to begin. To get the most out of your air compressor, whether you're a home or professional user, you'll need a dependable air hose.
We've pooled our years of knowledge to create the ideal buying guide for air hoses. Before you invest in new pneumatic equipment, we'll walk you through all of the decisions you'll need to make.
When Should You Replace Your Air Hose?
There are two reasons why you should replace your air hose. The first reason is that you want to enhance your air system so that you can utilise other tools or get more out of it. The second reason is that your existing air hose has a problem and needs to be replaced.
Choosing the Perfect Air Hose for You:
With so many different types of air hose to choose from, sorting through all of the options and information can be difficult. In truth, there are just four decisions to make before you begin your shopping:
- How long do you require a hose?
- What should the hose's internal diameter be?
- What kind of material should you use for your hose?
- Are you looking for a regular hose or a recoil hose?
¼ inch to 2 inch
10 bar to 30 bar
Cold Hose is a website dedicated to vehicle air conditioning hoses and fittings. A/C fittings, hoses, charge adapters, and oring seals are all available from us. All of the hoses and fittings are categorised by size and/or thread size. The speciality fittings page at Cold Hose has weld on barbs, compressor adapters, and much more. For additional information about custom hoses, please visit the custom hose page. Please contact us for further information if you require a bespoke fit. We are proud to stock only American-made fittings, and we are confident that you will enjoy their quality.
Most vehicles have advanced air conditioning systems. The AC high-pressure hose is responsible for transporting refrigerant from the compressor outlet to the receiver/drier, where it is cooled and used to produce cold air for the cabin.
¼ inch to 6 inch
Heavy-duty hoses with thicker, abrasion-resistant interiors are designed to transport coarse, rough, abrasive items such as rocks, chips, slurry, mud, pellets, and other abrasive materials. Most heavy material handling hoses were traditionally made of thick pure gum rubber, but improved compounding has allowed lower weight, more flexible hoses to reach the market, including urethane hoses.
As a general rule, the more expensive a hose is, the more durable its tube is in terms of wear; nevertheless, such hoses become less flexible and have less handling capabilities than thinner, lighter hoses. Material handling hoses have a limited lifespan and should be changed periodically to ensure even wear. Depending on the operating conditions, hours of use, and the product being transported, the service life may vary.
¾ inch to 2 inch
Use for sand blast